 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors fh36 series features 1. low-profile and light weight weight: reduced approximately 30% board footprint: reduced approximately 15% (as compared with hirose electric's fh26 series connectors (51 positions) 2. easy solderability on the pc board the soldering leads are on 0.6 mm pitch, exiting on front and back of the connector. 3. conducive traces on the pcb can run under the connector no exposed contacts on the bottom of the connector. 4. easy fpc insertion and reliable electrical connection proven flip lock actuator allows easy insertion of fpc and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 5. fpc position hold tabs on each side of the fpc assure correct placement and hold in the connector prior to closing of the actuator. 6. accepts standard fpc thickness 0.2mm thick standard flexible printed circuit (fpc) can be used. this is the only ultra-low profile zif connector using standard fpc. 7. board placement with automatic equipment flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. standard reel packaging contains 5,000 connectors. 8. halogen-free * (fh36w series) *as defined by iec61249-2-21 br-900ppm maximum, cl-900ppm maximum, cl + br combined-1,500ppm maximum 2010.9 new operation fpc temporary hold space saving (51 positions shown) [51 positions] can be mounted over conductive traces no exposed contacts on the bottom of the connector 16.9mm metal fittings do not protrude outside of the connector body 2.7mm 1.0mm max (1) actuator open (2) insert fpc (1) actuator open (2) insert fpc fpc fpc actuator actuator 1 2 3 4 (3) close the actuator (3) close the actuator (4) fpc connected (3) close the actuator (4) fpc connected t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n .
2 fh36 series0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors specifications storage temperature range storage humidity range -10 to +50c (note 3) relative humidity 90% max. (no condensation) note 1: when passing the current through all of the contacts, use 70% of the rated current. note 2: includes temperature rise caused by current flow. note 3: the term "storage" refers to products stored for a long period prior to mounting and use. the operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation. note 4: small blisters of the molding compounds in small areas will not affect form, fit or function. note 5: information contained in this catalog represents general requirements for this series. contact us for the drawings and specifications for a specific part number shown. item specification conditions rating current rating voltage rating 0.2 a dc (note 1) 30 vrms ac operating temperature range operating humidity range -55 to +85c (note 2) relative humidity 90% max. (no condensation) 1.insulation resistance 2.withstanding voltage 3.contact resistance 4.durability 5.vibration 6.shock 7.humidity (steady state) 8.temperature cycle 9.resistance to soldering heat 50 m? min no flashover or insulation breakdown 100 m? max. * including fpc conductor resistance contact resistance: 100 m? max. no damage, cracks, or parts dislocation no electrical discontinuity of 1 s or longer contact resistance: 100 m? max. no damage, cracks, or parts dislocation no electrical discontinuity of 1 s or longer contact resistance: 100 m? max. no damage, cracks, or parts dislocation contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation contact resistance: 100 m? max. insulation resistance: 50 m? min. no damage, cracks, or parts dislocation no deformation of components affection performance. 100 v dc 90 vrms ac / one minute 1 ma 10 cycles frequency: 10 to 55 hz, single amplitude of 0.75 mm 10 cycles in each of the 3 directions acceleration of 981m/s 2 , 6 ms duration, sine half-wave, 3 cycles in each of the 3 axis 96 hours at a temperature of 40c and humidity of 90 to 95% temperature:-55? ?+15? to +35??+85??+15? to +35? time: 30? 2 to 3 ? 30? 2 to 3 minutes 5 cycles 1) reflow: at the recommended temperature profile. 2) manual soldering: 350? 10? for 5 seconds recommended fpc thickness: 0.2?.03mm gold plated fh 36 w - 51s - 0.3 shw (50) ordering information series name : fh series no. : 36 blank :standard w :halogen-free (flame retardance ul94hb). number of positions : 11 to 61 contact pitch : 0.3mm termination type: smt horizontal staggered mounting type plating specifications (50)?old plating with nickel barrier 1 2 3 4 5 6 7 4 5 3 6 7 part material finish remarks insulator lcp color: beige ul94v-0 actuator pa fh36 series: dark brown fh36w series: light brown ul94hb contacts phosphor bronze gold plating ----------------- metal fittings pure tin reflow plating ----------------- materials 1 2 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 3 fh36 series 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors connector dimensions note 1 : the coplanarity of each terminal lead is within 0.1. note 2 : packaged on tape and reel only. check packaging specification. note 3 : slight discoloration in color of the plastic compounds does not affect form, fit or function of the connector. note 4 : after reflow, the terminal plating may change color, however this does not represent a quality issue. 0.1 1 1 0.1 a * * (2.7) (0.47) (0.25) (1.0 max) (2.75) a0.15 b0.1 c0.1 (1) (d: fpc insertion slot dimension) e0.1 lot no. indicator hrs mark number of contacts indicator cav no. (0.12) 0.60.1 0.60.1 (0.12) 0.30.1 all dimensions: mm tape and reel packaging (5,000 pieces/reel). order by number of reels. part number fh36-15s-0.3shw(50) fh36-17s-0.3shw(50) fh36-19s-0.3shw(50) fh36-25s-0.3shw(50) fh36-29s-0.3shw(50) fh36-33s-0.3shw(50) fh36-35s-0.3shw(50) fh36-45s-0.3shw(50) fh36-51s-0.3shw(50) fh36-61s-0.3shw(50) fh36w-11s-0.3shw(50) fh36w-15s-0.3shw(50) fh36w-17s-0.3shw(50) fh36w-19s-0.3shw(50) fh36w-23s-0.3shw(50) fh36w-27s-0.3shw(50) fh36w-31s-0.3shw(50) fh36w-33s-0.3shw(50) fh36w-39s-0.3shw(50) fh36w-51s-0.3shw(50) fh36w-61s-0.3shw(50) 580-1618-8-50 580-1606-9-50 580-1607-1-50 580-1619-0-50 580-1613-4-50 580-1615-0-50 580-1604-3-50 580-1617-5-50 580-1601-5-50 580-1600-2-50 580-1625-3-50 580-1623-8-50 580-1616-2-50 580-1612-1-50 580-1614-7-50 580-1608-4-50 580-1609-7-50 580-1622-5-50 580-1620-0-50 580-1605-6-50 580-1611-9-50 15 17 19 25 29 33 35 45 51 61 11 15 17 19 23 27 31 33 39 51 61 6.1 6.7 7.3 9.1 10.3 11.5 12.1 15.1 16.9 19.9 4.9 6.1 6.7 7.3 8.5 9.7 10.9 11.5 13.3 16.9 19.9 3.6 4.2 4.8 6.6 7.8 9 9.6 12.6 14.4 17.4 2.4 3.6 4.2 4.8 6 7.2 8.4 9 10.8 14.4 17.4 4.2 4.8 5.4 7.2 8.4 9.6 10.2 13.2 15 18 3 4.2 4.8 5.4 6.6 7.8 9 9.6 11.4 15 18 4.83 5.43 6.03 7.83 9.03 10.23 10.83 13.83 15.63 18.63 3.63 4.83 5.43 6.03 7.23 8.43 9.63 10.23 12.03 15.63 18.63 5.59 6.19 6.79 8.59 9.79 10.99 11.59 14.59 16.39 19.39 4.39 5.59 6.19 6.79 7.99 9.19 10.39 10.99 12.79 16.39 19.39 cl no. number of contacts a b c d e t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 4 fh36 series0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors (recommended metal mask thickness: t=0.1) (0.23:metal mask) (0.23:metal mask) b0.05 1.670.05 0.60.05 0.80.05 (0.5:metal mask) (0.65:metal mask) 0.30.03 0.30.03 0.60.05 0.30.05 0.60.05 0.5350.05 0.40.05 (0.3:metal mask) (0.2) (0.3) (0.7:metal mask) 0.950.05 c0.05 0.030.05 (3.07) 0.30.05 disengagement shift 2.20.3 0.10.15 0.750.1 0.850.1 0.60.02 1.450.1 r s j0.05 (0.2) 0.10.02 b0.03 g0.1 f0.1 0.3 +0.04 C 0.03 0.3 +0.04 C 0.03 0.30.07 0.30.02 h0.05 c0.03 0.30.07 0.20.03 3.30.3 (stiffener) 0.90.2 detail r (0.5) (0.07) *relative positions of point a and b a b 00.03 (lead plated 0.1 max) 2.40.1 (r0.2) (0.15) 1.150.05 1.650.05 r0.20.05 r0.20.1 r0.20.05 (r0.2) max r0.2 detail s r0.20.05 0.90.2 recommended pcb mounting pattern and metal mask dimensions recommended fpc dimensions all dimensions: mm part number fh36-15s-0.3shw(50) fh36-17s-0.3shw(50) fh36-19s-0.3shw(50) fh36-25s-0.3shw(50) fh36-29s-0.3shw(50) fh36-33s-0.3shw(50) fh36-35s-0.3shw(50) fh36-45s-0.3shw(50) fh36-51s-0.3shw(50) fh36-61s-0.3shw(50) fh36w-11s-0.3shw(50) fh36w-15s-0.3shw(50) fh36w-17s-0.3shw(50) fh36w-19s-0.3shw(50) fh36w-23s-0.3shw(50) fh36w-27s-0.3shw(50) fh36w-31s-0.3shw(50) fh36w-33s-0.3shw(50) fh36w-39s-0.3shw(50) fh36w-51s-0.3shw(50) fh36w-61s-0.3shw(50) 580-1618-8-50 580-1606-9-50 580-1607-1-50 580-1619-0-50 580-1613-4-50 580-1615-0-50 580-1604-3-50 580-1617-5-50 580-1601-5-50 580-1600-2-50 580-1625-3-50 580-1623-8-50 580-1616-2-50 580-1612-1-50 580-1614-7-50 580-1608-4-50 580-1609-7-50 580-1622-5-50 580-1620-0-50 580-1605-6-50 580-1611-9-50 15 17 19 25 29 33 35 45 51 61 11 15 17 19 23 27 31 33 39 51 61 3.6 4.2 4.8 6.6 7.8 9 9.6 12.6 14.4 17.4 2.4 3.6 4.2 4.8 6 7.2 8.4 9 10.8 14.4 17.4 4.2 4.8 5.4 7.2 8.4 9.6 10.2 13.2 15 18 3 4.2 4.8 5.4 6.6 7.8 9 9.6 11.4 15 18 6.04 6.64 7.24 9.04 10.24 11.44 12.04 15.04 16.84 19.84 4.84 6.04 6.64 7.24 8.44 9.64 10.84 11.44 13.24 16.84 19.84 5.6 6.2 6.8 8.6 9.8 11 11.6 14.6 16.4 19.4 4.4 5.6 6.2 6.8 8 9.2 10.4 11 12.8 16.4 19.4 4.8 5.4 6 7.8 9 10.2 10.8 13.8 15.6 18.6 3.6 4.8 5.4 6 7.2 8.4 9.6 10.2 12 15.6 18.6 4.6 5.2 5.8 7.6 8.8 10 10.6 13.6 15.4 18.4 3.4 4.6 5.2 5.8 7 8.2 9.4 10 11.8 15.4 18.4 cl no. number of contacts b c f g h j t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 5 fh36 series 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors copper foil cover adhesive covering film layer reinforcement material adhesive stiffener recommended fpc construction 1. using single-sided fpc 2. using double-sided fpc 3.precautions material name surface treatment copper foil base adhesive base film reinforcement material adhesive stiffener material material thickness (m) cu 1oz thermosetting adhesive polyamide 1 mil thick thermosetting adhesive polyamide 3 mil thick total 0.2m thick gold plated over 1 to 5m thick nickel underplating covering film layer cover adhesive polyamide 1 mil thick. 3 35 25 25 40 75 203 (25) (25) covering layer film cover adhesive surface treatment through-hole copper copper foil base adhesive base film base adhesive cu 1 /2oz thermosetting adhesive polyamide 1 mil thick thermosetting adhesive polyamide 1 mil thick total (18) 25 25 25 25 197 polyamide 1 mil thick cu cu 1 /2oz thermosetting adhesive polyamide 1 mil thick thermosetting adhesive (25) (25) 3 15 18 18 25 18 material name material material thickness (m) * to prevent release of the fpc due to its bending, use of the double sided fpc with copper foil on the back side is not recommended. 1. this specification is a recommendation for the construction of the fh36 series fpc (t=0.2 ? 0.03) 2. for details about the construction, please contact the fpc manufacturers. connecting side back side connecting side back side 0.2m thick gold plated over 1 to 5m thick nickel underplating contact fpc manufacturer for specific details. t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 6 fh36 series0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors packaging specification embossed carrier tape dimensions (tape width of 24mm max.) embossed carrier tape dimensions (tape width of 32mm min.) reel dimensions 20.15 40.1 (1.5) (2.95) (3.85) (1) (n) flat surface, for placement with automatic equipment. k0.3 m0.1 80.1 ?1.5 +0.1 0 1.750.1 (0.3) unreeling direction k0.3 l0.1 m0.1 1.750.1 ?1.5 +0.1 0 1.7 +0.15 0 1.5 +0.1 0 (1.5) 20.15 40.1 (n) (0.3) 80.1 flat surface, for placement with automatic equipment. (q:outside) (p:inside) (?13) (?80) (?380) (25 pockets min.) (25 pockets min.) end section mounting section embossed carrier tape no connector inserted lead section (400mm min.) no connector inserted top cover tape all dimensions: mm part number fh36-15s-0.3shw(50) fh36-17s-0.3shw(50) fh36-19s-0.3shw(50) fh36-25s-0.3shw(50) fh36-29s-0.3shw(50) fh36-33s-0.3shw(50) fh36-35s-0.3shw(50) fh36-45s-0.3shw(50) fh36-51s-0.3shw(50) fh36-61s-0.3shw(50) fh36w-11s-0.3shw(50) fh36w-15s-0.3shw(50) fh36w-17s-0.3shw(50) fh36w-19s-0.3shw(50) fh36w-23s-0.3shw(50) fh36w-27s-0.3shw(50) fh36w-31s-0.3shw(50) fh36w-33s-0.3shw(50) fh36w-39s-0.3shw(50) fh36w-51s-0.3shw(50) fh36w-61s-0.3shw(50) 580-1618-8-50 580-1606-9-50 580-1607-1-50 580-1619-0-50 580-1613-4-50 580-1615-0-50 580-1604-3-50 580-1617-5-50 580-1601-5-50 580-1600-2-50 580-1625-3-50 580-1623-8-50 580-1616-2-50 580-1612-1-50 580-1614-7-50 580-1608-4-50 580-1609-7-50 580-1622-5-50 580-1620-0-50 580-1605-6-50 580-1611-9-50 15 17 19 25 29 33 35 45 51 61 11 15 17 19 23 27 31 33 39 51 61 16 16 16 24 24 24 24 24 32 32 16 16 16 16 24 24 24 24 24 32 32 ?| ?| ?| ?| ?| ?| ?| ?| 28.4 28.4 ?| ?| ?| ?| ?| ?| ?| ?| ?| 28.4 28.4 7.5 7.5 7.5 11.5 11.5 11.5 11.5 11.5 14.2 14.2 7.5 7.5 7.5 7.5 11.5 11.5 11.5 11.5 11.5 14.2 14.2 6.3 6.9 7.5 9.3 10.5 11.7 12.3 15.3 17.1 20.1 5.1 6.3 6.9 7.5 8.7 9.9 11.1 11.7 13.5 17.1 20.1 17.4 17.4 17.4 25.4 25.4 25.4 25.4 25.4 33.4 33.4 17.4 17.4 17.4 17.4 25.4 25.4 25.4 25.4 25.4 33.4 33.4 21.4 21.4 21.4 29.4 29.4 29.4 29.4 29.4 37.4 37.4 21.4 21.4 21.4 21.4 29.4 29.4 29.4 29.4 29.4 37.4 37.4 cl no. number of contacts k l m n p q t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 7 fh36 series 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors temperature profile hrs test condition solder method :reflow, ir/hot air environment :room air solder composition :paste, 96.5%sn/3.0%ag/0.5%cu (senju metal industry, co., ltd.'s part number:m705-221cm5-32-10.5) test board :glass epoxy 25mm50mm0.8mm thick land dimensions :0.3mm0.6mm, 0.3mm0.8mm metal mask :0.230.5, 0.230.650.1mm thick the temperature profiles shown are based on the above conditions. in individual applications the actual temperature may vary, depending on solder paste type, volume / thickness and board size / thickness. consult your solder paste and equipment manufacturer for specific recommendations. 25? (60sec.) (60sec.) 90 sec. to 120 sec. preheating soldering start (?) temperature 0 50 100 150 200 250 max 250? time (seconds) 150? 200? 230? using lead-free solder paste t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 8 fh36 series0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors rotate down the actuator until firmly closed. 3 operation and precautions operation 1. fpc insertion procedure. connector installed on the board. lift up the actuator. use thumb or index finger. 2. fpc removal lift up the actuator pull up the fpc at an angle of approximately 10 ? and than with- drew it from the connector ?. 1 1 insert the fpc (contact surfaces facing down) at angle of approximately 10 to the board surface ?, making sure that the fpc positioning tabs clear the protrusions on both sides of the connector. lower the fpc down ?, parallel to the board surface. 2 fpc contact surface faces downward protrusions for the fpc positioning. 10 ? ? protrusions for fpc positioning 10 125 ? ? t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 9 fh36 series 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors precautions exercise care when handling connectors. follow recommendations given below. [ precautions when mounting connectors on the pcb ] handling before mounting on pcb insertion of the fpc or operation of the actuator prior to mounting on the pcb is not recommended. pc board warpage minimize the warpage as much as possible. the connector is straight within 0.1 mm max. make sure that the mount- ing area flatness can accept the connector terminals without causing any failure of the solder joints. when braking the large pc board into individual boards exercise care not to damage the installed connectors. when attaching the boards or other components with the screws make sure that any stresses will not cause board deflections affecting the mounting areas of the connector. bending of the board for a board width of 100 mm, bending of the board must be 0.5 mm max. (ref to fig. 1) 100 0.6 0.5max f connector board 100 0.6 0.5max connector board f axis of rotation 2 assure free rotation of the actuator. [ precautions during fpc insertion and mating ] pay attention to the following points when inserting fpc. actuator operation 1 do not apply excessive force when opening the actuator prior to fpc insertion. when opening make sure that the force is applied only to the actuator itself, avoiding touching of the contacts. damage to the actuator damage to the actuator actuator fig. 1 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 10 fh36 series0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors precautions the actuator will rotate 125 ?. do not apply force to rotate further. 3 when opening or closing the actuator, do so at the cen- ter section. 4 do not grasp or and lift the actuator (fig. 3) nor insert the nail from the back of it (fig. 4). 5 fpc insertion do not insert the fpc at any high angle from above. 125 protrusions for fpc positioning 10 fig. 3 fig. 4 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 11 fh36 series 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors precautions as illustrated (fig. 5) angle insertion may cause electrical discontinuity when the fpc is deflected in use. verification of the fully closed actuator the fpc should be fully inserted, with its positioning tabs fully behind the protrusions on both sides of the con- nector? insertion slot (fig. 6). protrusions fpc positioning fpc positioning tab [ routing of the fpc (fpc fully inserted / actuator closed) ] do not apply any pull or upward-directed force to the fpc. do not make any sharp bends of fpc close to the immediate exit from the connector (fig. 7) to avert insertion of the fpc at an angle, consideration should be given to securing enough insertion space when designing the board lay-out. insertion will be difficult when the fpc is too short. contact fpc manufacturer for information about the bending specifications. opening of the fpc pattern fig. 5 fig. 7 fig. 6 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . 12 fh36 series0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connectors the contents of this catalog are current as of date of 09/2010. contents are subject to change without notice for the purpose of improvements. 5-23,osaki 5-chome,shinagawa-ku,tokyo 141-8587,japan phone: 81-3-3491-5300, fax: 81-3-3495-5230 http://www.hirose.com http://www.hirose-connectors.com protrusions for fpc positioning 10 125 precautions [ removing of the fpc ] rotate the actuator to the fully open position (max. angle of 125 ?) lift the fpc approximately 10 ? (making sure that the positioning tabs clear the protrusions on both sides) and carefully withdraw it from the connector. [ other precautions ] hand soldering precautions when hand soldering: do not perform reflow or hand soldering with the fpc inserted in the connector. do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. do not use excessive amount of solder or flux compounds. operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds. 1 2 3 t h e p r o d u c t i n f o r m a t i o n i n t h i s c a t a l o g i s f o r r e f e r e n c e o n l y . p l e a s e r e q u e s t t h e e n g i n e e r i n g d r a w i n g f o r t h e m o s t c u r r e n t a n d a c c u r a t e d e s i g n i n f o r m a t i o n . |
Price & Availability of FH36W-61S-03SHW
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |